abouillot PiGateway interfacing

[rbihler]

I am a noob and have been combing the messages and have not been able to find the answer I am looking for.  I am pretty sure I am missing a minor detail, but missing it all the same.  

I have Aboullots Pi Gateway up and what I think running.  I am also using his arduino code with some modifications as I was not able to compile with the DMT library I have.  I just changed the dmt section and it sending valid data.  I am not able to receive the temp or humidity messages into open. Hab.  If I run the SenderReceiver -r command I see the same data packets that are coming into the log file.  

I see the 101/14/6 data come in as listed below in the log, var2 and var3 are the data I would like. 
I am also seeing 101/14/7 come in, the RGB data packets.  
When I press the toggle red/green or blue I see the data lite on the arduino flash and a message in the log.  

I am hoping this is something pretty simple, but I am stumped.  I have changed the items file so many different ways hoping to see the data come in.  


***My Openhab configurations transport section. 
# URL to the MQTT broker, e.g. tcp://localhost:1883 or ssl://localhost:8883

mqtt:rfmPiMosquitto.url=tcp://localhost:1883



mqtt:frmPiMymosquitto.qos=0



mqtt:rfmPiMosquitto.retain=true



mqtt:rfmPiMosquitto.async=true


***Items: 
Group All

Group gGroundFloor (All)

Group GF_Living "Living Room" <video> (gGroundFloor)

Number MyFirstSensor "Temperature [%.1f F]" (GF_Living) {mqtt="<[rfmPiMosquitto:RFM/101/14/6/var2:state:default]"}





Number itm_garage_dist "Garage Dist [%.1f Inch]" (ALL){mqtt="<[rfmPiMosquitto:RFM/101/14/7:var2:state:default]"}

Contact itm_my_gar_door "Garage Door Status [MAP(en.map):%s]" <garage> (ALL)



Switch LivingLedRedSwitch {mqtt=">[rfmPiMosquitto:RFM/101/14/7:command:OFF:0,0,0],>[rfmPiMosquitto:RFM/101/14/7:command:ON:0,1,0"}

Switch LivingLedBlueSwitch {mqtt=">[rfmPiMosquitto:RFM/101/14/7:command:OFF:0,0,0],>[rfmPiMosquitto:RFM/101/14/7:command:ON:1,0,0"}

Switch LivingLedGreenSwitch {mqtt=">[rfmPiMosquitto:RFM/101/14/7:command:OFF:0,0,0],>[rfmPiMosquitto:RFM/101/14/7:command:ON:0,0,1"}


***My messages Log File, I am sure the messages are coming in.  
Sep 12 22:12:22 raspberrypi Gatewayd[750]: [14] to [1]

Sep 12 22:12:22 raspberrypi Gatewayd[750]: Received Node ID = 14 Device ID = 6 Time = 9021472 RSSI = -92 var2 = 24.100000 var3 = 42.000000



Thanks
Ron

[greginkansas]

Is the problem openhab not getting the MQTT messages?

[rbihler]

Yes I am not getting the temperature/humidity messages from the arduino into openhab.  I am seeing the temperature/humidity messages in the messages file in the Log (From PiGateway) 

If I toggle the RGB output within Openhab it is controlling the outputs on the arduino.  
I am just not getting these messages into openhab.  I can't quite figure out the format needed. 

Ron

[greginkansas]

I remember this line having to be right


# Optional. Defines the last will and testament that is sent when this client goes offline
# Format: topic:message:qos:retained <br/>
mqtt:mosquitto.lwt=openhab:1:0:false

[rbihler]

I just tried that, No luck. I will leave it is as I don't think it hurts.
Here are some of the things I tried. Since I can change the output of the arduino using the item
Switch LivingLedRedSwitch {mqtt=">[rfmPiMosquitto:RFM/101/14/7:command:OFF:0,0,0],>[rfmPiMosquito:RFM/101/14/7:command:ON:0,1,0"}

This works on the arduino, I see the pins change state.

I have tried:
Number MyFirstSensor "Temperature [%.1f F]" (GF_Living) {mqtt="<[rfmPiMosquitto:RFM/101/14/6:state:default:0,1,0]"}
The temperature data is sent on RFM/101/14/6 It comes in with 3 variables Time, Var2, Var3

I have tried the above line with 101/14/6:var2:state:default]"} as the last part of the line.

I am about to scrap this method of using the PiGateway (Radio is attached to the PI) and use the ardruino gateway. But I am sure the data is there, I just can't figure out how to pull it into openhab.
Again the PiGateway program adds a line to the log file so I am even sure it's getting the data. It works outbound with sending the switch data.

I know I am close, I tried a bunch of different Item configurations. NO luck at all.

[greginkansas]

Try this

{mqtt="<[rfmPiMosquitto:RFM/101/14/6:state:default::]"}

[laspencia brown]

were you able to get it working because I'm still not getting openhab status to update